OTC 5039 Charged Air Cooler Tester for Class 7 and Class 8 Trucks

OTC 5039 Charged Air Cooler Tester for Class

This is the easy way to find air leaks in the charged air cooler systems used on class 7 and 8 truck engines. The tester features a large 2-1/2" 0-60 PSI pressure gauge regulator and relief valve and two safety cables. It also has quick disconnect air fittings that attach to a 3" 3-1/2" or 4" cooler hose.

  • Brand: OTC
  • ASIN: B00063XRGA
  • UPC: 731413005640

OTC 5042 Injector Puller Set for Cummins

OTC 5042 Injector Puller Set for

OTC Injector Puller Set for Cummins helpful puller will handle a variety of injectors found in Cummins engines: mechanical L-10 PDT and PTD top-stop 855NH. Its two-jaw design firmly grips the injector while it is being removed by the slide hammer. It includes storage case and special adapter for pulling STC injectors.

  • Brand: OTC
  • ASIN: B00063X0JE
  • UPC: 731413005732

OTC 5081 S-Cam Air Brake Spring Tool

OTC 5081 S-Cam Air Brake Spring

Safely replace brake shoes on heavy-duty tractors and trailers. Simply hook the retaining spring loop and press down against the axle.

  • Brand: OTC
  • ASIN: B000GTMJUO
  • UPC: 782386206473

ABN Pneumatic Vacuum Brake and Clutch Bleeder Kit, 0.75 Liter – Master Cylinder 90–120 PSI Air Pressure Fluid Bleed Tool

ABN Pneumatic Vacuum Brake and Clutch Bleeder Kit,

Instead of putting up with the mess and inconvenience of a hand pump, use the ABN Pneumatic Vacuum Brake and Clutch Bleeder Kit, 0.75 Liter - Master Cylinder 90-120 PSI Air Pressure Fluid Bleed Tool to quickly bleed stubborn brake lines. Simply apply 90 to 120 PSI air pressure from your own compressor, take off the master cylinder reservoir cap, open the bleeder, and hook up the tool's hose. When you press the trigger, it allows air to run through canister holes which creates suction on the line going to the brake nipple on the caliper which will suck out the dirty fluid and air. This design allows for a one-person job on motorcycles, cars, and trucks. The refill container holds 25 fluid ounces and different adapter sizes are included to accurately fit your application. WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

  • Brand: ABN
  • ASIN: B076CTLV4R
  • UPC: 688295879695

OTC 5038 Brake Anchor Pin and Pin Bushing Service Set

OTC 5038 Brake Anchor Pin and Pin Bushing

With this service kit there is no need to remove the bearing hub assembly just to replace the pins and bushings on 16-1/2" S-Cam trailer and tractor "Q" brake systems. Much less complicated and time consuming! Special tooling and our C-frame press get you past the hub assembly so you can do the job quickly and professionally without damaging other parts. Includes everything needed for removal and replacement.

  • Brand: OTC
  • ASIN: B000HI0Q04
  • UPC: 731413031816

OTC 7117 Fuel Injector Nozzle Puller for Caterpillar

OTC 7117 Fuel Injector Nozzle Puller for

OTC Fuel Injector Nozzle Puller for Caterpillar are designed this nozzle puller to remove pencil nozzles on Cat engines. The tool applies straight even pulling power through a bridge assembly and mechanical forcing screw. The job is done quickly and without damage. It works on Caterpillar 1100/3208 diesel engines.

  • Brand: OTC
  • ASIN: B00063YWB4
  • UPC: 731413003981

OTC 7180 Universal Bearing Cup Installer

OTC 7180 Universal Bearing Cup

Universal Bearing Cup Installer can be used to install cups ranging in size from 3-5/8 inch O.D. to 6-1/2 inch O.D. Simply turn the expander to the left or right to adjust the installer jaw diameter to the approximate same size as the bearing cup inside diameter. Finger tighten the nut to prevent the expander from moving once the jaw diameter has been set and install the bearing cup.

  • Brand: OTC
  • ASIN: B000O80ASU
  • UPC: 731413010071

OTC 7455 Fuel Injector Nozzle Tool for Mack

OTC 7455 Fuel Injector Nozzle Tool for

OTC Fuel Injector Nozzle Tool for Mack Here's a handy tool for removing or installing injector nozzles on Mack E-6 4 VH and E-9 4 VH four-valve engines. The puller threads directly into the nozzle holder and mechanical screw power does the pulling while a cylindrical guide holds the injector steady. It includes gauge to ensure correct injector depth during installation.

  • Brand: OTC
  • ASIN: B00063YWBO
  • UPC: 731413011047

OTC 7453A Diesel Fuel Line Wrench

OTC 7453A Diesel Fuel Line

OTC Diesel Fuel Line Wrench Fuel line nuts are often hard to reach, but these unique 3/8 inch square-drive tools solve that problem. With them, you can loosen or tighten fuel lines at the fuel injector nozzle or fuel injection pump without damaging the nut. Fuel line wrench, 2.6 inch long. For International DT466 and 9L diesel engines. It fits 19 mm fuel line nuts. It is similar to Ford No. 303-230 (T83T-9396-A).

  • Brand: OTC
  • ASIN: B00063YWIM
  • UPC: 731413003479

Yellow Jacket 69562 4 oz Oil Injector

Yellow Jacket 69562 4 oz Oil

Body and cap are rugged aluminum with an “O” ring seal. Male fitting is at one end of short length of hose with Schrader.

  • Brand: Yellow Jacket
  • ASIN: B0039V07W8
  • UPC: 686800695624
Similar Air Injector Cap Shopping Results