Toyota/Lexus Crankshaft Damper Pulley Holding Holder Harmonic Tool with 2PCS Crank Bolts

Toyota/Lexus Crankshaft Damper Pulley Holding Holder Harmonic Tool

Anyone that is trying to replace timing belt and water pump definitely need this tool, it will save you a lot of headaches and bloody knuckles! This holding tool works with the following engines: Toyota 1996 and later: 3.0 V6, 3.3 V6, 4.0 V6, 4.7 V8. also 4 cyl: 1983-1995 22RE, 1995-2004 2RZ & 1995-2004 3RZ Lexus 1990 and later: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, 4.7 V8, (Noted: Item does not come with any instructions and packaging / color maybe varied. Proper use of this professional auto tools are important to prevent from any unnecessary injuries.) Features: ☆Developed to aid in the removal and installation of the crank bolt on Lexus and Toyota engines ☆The bolt is extremely tight and removal is extremely difficult at best ☆Factory specifications require up to 280 pounds of torque to seat the pulley properly. This tool allows the factory torque to be attained ☆This special tool is needed to remove the crank shaft bolt - no factory tool available ☆Hole in center of tool - allows access to removal of crank shaft bolt. ☆Offset breaker bar attachment point - allows easy removal and replacement of crank shaft bolt to factory torque specifications ☆Low profile design - no need to remove radiator or other components to access and remove Harmonic Damper P...

  • Brand: E-cowlboy
  • ASIN: B07Q1W36L7

Massive High Strength Standard Length Reusable Crank Pulley Damper Bolt Compatible w/GM LS V8 LSX LS1 2 3 4 5 6 ARP Style

Massive High Strength Standard Length Reusable Crank Pulley

Works with ALL LSX Engines (except LS7 or other OEM dry sump - see our other listings for those applications). Grade 12.9 197,000 PSI tensile strength 12 point flanged bolt finished in black oxide is far stronger and places superior clamp only load to balancer through the use of a separate washer plate (a full 1/4" thick!) versus the 1 piece stocker. Fully reusable.

  • Brand: Massive Speed System
  • ASIN: B06XQQBT1G

ACDelco 12588670 GM Original Equipment Timing Chain Damper Kit with Bolt, Retainer, and Spacer

ACDelco 12588670 GM Original Equipment Timing Chain Damper

ACDelco GM Original Equipment Engine Timing Damper Kits remove unnecessary slack from the timing chain to help prevent chain rattle and excessive component wear, and are GM-recommended replacements for your vehicle’s original components. These original equipment engine timing damper kits contain components that will provide the same performance, durability, and service life you expect from General Motors.

  • Brand: ACDelco
  • ASIN: B004AFISA0
  • UPC: 707773785027

Sunluway Lexus & Toyota Harmonic Damper Pulley Holding Crankshaft Crank Holder Tool

Sunluway Lexus & Toyota Harmonic Damper Pulley Holding

Why choice our Lexus/Toyota Crankshaft Crank Harmonic Damper Pulley Holding Holder Tool? A MUST HAVE TOOL--Factory specifications require up to 280 pounds of torque to seat the pulley properly. This tool allows the factory torque to be attained. This special tool is needed to remove the crank shaft bolt - no factory tool available. Lexus/Toyota Crankshaft Crank Harmonic Damper Pulley Holding Holder Tool Helps remove and install the crank bolt more easily and simple on many Toyota & Lexus engines. *Applicable: TOYOTA, LEXUS*Fitment: 1. Fits Toyota '96 and up 3.0, 3.3, 4.0, V6, 4.7, V8 plus '83 - '95 4-cyl. 22RE, '95 - '04 4-cyl., 2.4 RZ and 2.7 3RZ engines 2. Also fits Lexus '90 and up 3.0 L6, 3.0, 3.3 V6 and 4.0, 4.3 and 4.7 V8 engines *Material : BEST QUALITY, 42CrMo STEEL*Function: Sunluway CTA Toyota / Lexus Harmonic Dampening Tool Holds the crankshaft while tightening the crank bolt. *Wide Usege: Allows user to hold crankshaft while tightening the crank bolt with a torque wrench. Developed to aid in the removal and installation of the crank bolt on Lexus and Toyota engines. Offset breaker bar attachment point - allows easy removal and replacement of crank Low profile Harmonic Damper Pulley. Hole in center of tool - allows access to removal of crank shaft bolt. Buy it with...

  • Brand: Sunluway
  • ASIN: B07Q29ZMMY

TruBuilt 1 Automotive Universal Harmonic Balancer, Pulley, Damper and Gear Puller Tool Set, 13 Pieces, with Carrying Case T1A-D1007

TruBuilt 1 Automotive Universal Harmonic Balancer, Pulley, Damper

Excellent professional quality and competitive price, for automotive and machine repair. This puller set removes balancers, pulleys and gears with taped holes. A floating swivel prevents damage to the shaft end. Four slots in the yoke allow for 2- or 3-hole applications. Tool bolts to balancer with center screw on the end of the crankshaft. Tighten while tapping on the screw head to remove balancer.Backed by a total satisfaction 100% money back guarantee. Evaluate the tools for a full 30 days and if you are not 100% totally happy with the tools, just return them to us and we will refund your purchase. We know our tools are high quality and that is why we can offer such an amazing guarantee. All our tools come with a full 1 year warranty from defect.

  • Color: Black, Silver
  • Brand: TruBuilt 1 Automotive
  • ASIN: B010DF913S
  • UPC: 685784983819

PIONEER Harmonic Balancer Damper+BOLT compatible with Chevy SB 283 305 327 350 383 8" INT Balanced

PIONEER Harmonic Balancer Damper+BOLT compatible with Chevy SB

This listing is for a Pioneer OE-Replacement balancer (damper) and bolt for Chevrolet GEN I small block V-8 engines requiring an internally (neutral) balanced 8" OD balancer. P/N DA-3502 + 859012. Balancer specifications are as follows (all measurements are in inches): ENGINE BALANCE: Internal SAFETY RATING: Not SFI approved DEGREE MARKINGS: Yes OUTSIDE DIAMETER: 7.99" MATERIAL: Nodular iron CONSTRUCTION: Elastomer FINISH: Black painted CRANK BORE: 1.24" NOSE DIAMETER: 1.88" WEIGHT: 11.02 lbs. OVERALL WIDTH: 2.34"

  • Brand: IE PARTS GROUP
  • ASIN: B07CK4V2VH

Yoursme Lexus and Toyota Crankshaft Damper Pulley Holder Harmonic Damper Pulley Holding Tool

Yoursme Lexus and Toyota Crankshaft Damper Pulley Holder

This holding tool is a needed item to remove the crank shaft bolt-no factory tool available. Fitment:Lexus 1990 and later: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, and 4.7 V8. Toyota 1996 and later: 3.0 V6, 3.3 V6, 4.0 V6, 4.7 V8. 4 cyl: 1983-1995 22RE, 1995-2004 2RZ & 1995-2004 3RZ Usage: Factory specifications require up to 280 pounds of torque to seat the pulley properly. This tool allows the factory torque to be attained.Offset breaker bar attachment point - allows easy removal and replacement of crank shaft bolt to factory torque specifications. Package includes:1*Harmonic Damper Pulley Holding Tool2* bolts & 2 washers No hesitation, take this holding tool home and make the installation of your crank bolt easier.

  • Brand: Yoursme
  • ASIN: B07QPNNC55

Genuine Honda 90121-S0A-000 Damper Fork (12X98) Bolt

Genuine Honda 90121-S0A-000 Damper Fork (12X98)

HONDA OEM Front Suspension-Fork Lower Bolt 90121S0A000 Seller & Payment Information Seller name:whiteracingproductsllc_nosSee our other listingsWe Accept: Customer Support If you have questions about the product or your order please contact us via Messages for assistance. Thank youBusiness Hours: 9 am to 5:30 pm est Shipping & Handling Shipping Service:Please refer the shipping sectionShipping Cost:Please refer the shipping sectionShip-to location:Please refer the shipping sectionOrder Processing Time:15 business daysAbout the Part Part Number: 90121S0A000 The part or sub-assembly you are purchasing is a Genuine OEM Factory Original part sold by an authorized Genuine OEM parts re-seller. All the Honda listed items that have this caveat are drop shipped directly to you the end user, from the OEM manufacturer. While we make every attempt to keep OEM inventory updated with qty and stock, on the rare occasion the OEM will advise us the item stock is depleted and no longer available. Should this be the case, we will make every effort to source the part, if we are not successful, then a full 100% refund will be issued within 24 hours of ordering. We are not inventorying these Honda OEM parts, if you see the listing and you already know Honda has the part on national back-order, o...

  • Color: Regular
  • Brand: Honda
  • ASIN: B00P6NW1TY

PIONEER Harmonic Balancer Damper+BOLT compatible with Chevy SB 383 400 8" EXTERNAL

PIONEER Harmonic Balancer Damper+BOLT compatible with Chevy SB

This listing is for a Pioneer OE-Replacement balancer (damper) and bolt for early model Chevrolet small block 400ci V-8 engines. P/N DA-400 + 859012. Balancer specifications are as follows (all measurements are in inches): ENGINE BALANCE: External SAFETY RATING: Not SFI approved DEGREE MARKINGS: Yes OUTSIDE DIAMETER: 7.99" MATERIAL: Nodular iron CONSTRUCTION: Elastomer FINISH: Black painted CRANK BORE: 1.24" NOSE DIAMETER: 1.88" WEIGHT: 10.77 lbs. OVERALL WIDTH: 2.34"

  • Brand: IE PARTS GROUP
  • ASIN: B07MZDSLCN

Massive High Strength Extra Length Reusable Crank Pulley Damper Bolt Compatible w/GM LS V8 LSX LS1 2 3 4 5 6 ARP Style

Massive High Strength Extra Length Reusable Crank Pulley

XL Series! 10mm extra length provides MORE thread engagement! Still fits ALL LS Motors '97- today except Dry Sump. Perfect for getting proper thread engagement on those DAMAGED crank snout threads!!! Did you (or someone else?) use a stock or other bolt to attempt to draw down the press fit crank pulley? Those who have tried this soon realize the first several threads will be pulled out of the crank... often rendering the crank useless. Massive has released this new XL-LS Extended length bolt that travels further into the threaded crank snout to engage more thread, giving your damaged crankshaft new life. The OEM bolt only engages the last 22mm of thread. Our new XL-LS bolt offers 32mm of engagement, a 50% increase. So even if the first few mm of your crank threads are damaged, merely clean out any material, and you will obtain proper or even increased thread bond! Others have used the superior torque transfer on their crank driven supercharged cars for enhanced clamp load. Our bolt is a full 10mm longer than the OE or ARP bolt. Because, who couldn't use an extra 10mm? Works with ALL LSX Engine (except LS7 or other OEM dry sump - see our othre listings for those applications). Grade 12.9 197,000 PSI tensile strength 12 point flanged bolt finished in black oxide is far stronger and...

  • Brand: Massive Speed System
  • ASIN: B06XQQQS4Z

ARP 2342503 Stud Kit

ARP 2342503 Stud

Chevrolet Gen III/LS Series Small Block (except LS7), 1-1/16 socket size, M16 x 2.0 Diameter/Thread size, 4.325 Under Head Length, ARP 234-2503 Harmonic Balancer Bolt KitARP Chevy Harmonic Balancer BoltsAs the crankshaft flexes and twists, the balancer absorbs incredible amounts of kinetic energy. To ensure that the balancer is locked in position ARP has developed these ultra strong 200,00 psi bolts that let you exert maximum clamping force. ARP Chevy Harmonic Balancer Bolts has Special features include 1/4 thick, wide area washer and an extra tall 12-point head that accepts a deep socket and elimates the worry of stripping the head.

  • Brand: ARP
  • ASIN: B001D0MJNC
  • UPC: 672036030315

Big-Autoparts SBC Harmonic Balancer Bolt Small Block Damper for Chevy 280 305 350 383

Big-Autoparts SBC Harmonic Balancer Bolt Small Block Damper

SB-Chevy, 7/16''-20 x 2-1/4'' SBC Balancer Bolt Harmonic Chevy 280 305 350 383 Small Block Damper Grade 8 Material Heat-Treated For Strength Hex Prevents Socket Slippage Accurate and Uniform Torque Black Plated Finish

  • Color: Metal yellow
  • Brand: big-autoparts
  • ASIN: B071NJ5NFM
  • UPC: 780330803518

Rough Country 8749430 Steering Stabilizer

Rough Country 8749430 Steering

Steering stabilizers are designed to restrain "bump steer" and front end vibration, giving added life to tires, ball joints, and other steering components.

  • Color: 2014-2019
  • Brand: Rough Country
  • ASIN: B07D3BP377
  • UPC: 843030146726

MOSTPLUS Damper Crankshaft Crank Pulley Holder Wrench Holder Removal Tool for Honda Acura Harmonic 50mm

MOSTPLUS Damper Crankshaft Crank Pulley Holder Wrench Holder

FITMENT: 1990-1997 Honda Accord 2.2L 4 cyl.1996-1997 Honda Accord 2.7L V-61998-newer Honda Accord 2.3L 4 cyl. & 3.0L V-61992-newer Honda Civic 1.6L 4 cyl.1997-newer Honda CR-V 2.0L 4 cyl.1993-1997 Honda Del Sol 1.6L 4 cyl. 2000-newer Honda Insight 1.0L 3 cyl.1995-1997 Honda Odyssey 2.2L 4 cyl.1998 Honda Odyssey 2.3L 4 cyl.1999-newer Honda Odyssey 3.5L V-61992-newer Honda Prelude 2.2L 4 cyl.1992-1996 Honda Prelude 2.3L 4 cyl.2000-newer Honda S2000 2.0L 4 cyl.1997 Acura CL 2.2L 4 cyl.1997-1998 Acura CL 3.0L V-61998-1999 Acura CL 2.3L 4 cyl.2000-newer Acura CL 3.2L V-61990-1992 Acura Integra 1.6L 4 cyl.1992-1993 Acura Integra 1.7L 4 cyl.1993-newer Acura Integra 1.8L 4 cyl.1991-1995 Acura Legend 3.2L V-61996-newer Acura RL 3.5L V-61995-newer Acura TL 3.2L V-6

  • Brand: MOSTPLUS
  • ASIN: B07C1YT2GP

Orange Cycle Parts Fork Damper Tube Bolt Kit for Harley Big Twin/Sportster XL w/Showa Forks 8mm only Replaces # 45405-75A

Orange Cycle Parts Fork Damper Tube Bolt Kit

8mm Fork Damper Tube Bolt Kit For Harley Big Twin 1975 - 2017 / Sportster XL 1973 - 2017 w/ Showa Forks Replaces Harley OEM # 45405-75A Check OEM # for precise application Includes: (2) 8mm-1.25 x 16mm chrome steel socket head screws (2) 8mm copper washers Sold as a pair

  • Color: Metallic
  • Brand: Orange Cycle Parts
  • ASIN: B075S781Q4

Massive High Strength LS7 Reusable Crank Pulley Damper Bolt Compatible w/GM LS V8 LSX LS 7 9 LSA LS3 GS Dry Sump Length ARP Style

Massive High Strength LS7 Reusable Crank Pulley Damper

LS7 SERIES CRANK BOLT - Truly superior strength is needed on this most critical of load bearing fasteners. The crankshaft sees immense kinetic energy! Both twisting and lateral loads are exerted on this one area, and to an even greater degree on belt driven supercharged cars. OEM fasteners are one-time-use - they stretch and must be replaced, so upgrading with the Massive Speed Precision unit is a "no-brainer". Grade 12.9 197,000 PSI tensile strength 12 point flanged bolt finished in black oxide is far stronger and places superior clamp only load to balancer through the use of a seperate washer plate (a full 1/4" thick! Fully reusable. MADE IN THE USA!!! Designed for OEM Dry sumped LS engines, such as the LS7, LS9 the Gran Sport Corvette etc

  • Brand: Massive Speed System
  • ASIN: B06XQPPCFL

Sunluway for Lexus and Toyota Harmonic Damper Pulley Holding Tool Crankshaft Crank Holder Removal Wrench Tool

Sunluway for Lexus and Toyota Harmonic Damper Pulley

Wanna Save Energy and Time When Removing and Installing the Crank Bolt ? Sunluway tool is a lifesaver if you work on toyota / lexus timing belts or just need to remove the crankshaft pulley. Fitment: Lexus 1990 and later: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, 4.7 V8; Toyota 1996 and later: 3.0 V6, 3.3 V6, 4.0 V6, 4.7 V8; 4 cyl: 1983-1995 22RE, 1995-2004 2RZ & 1995-2004 3RZ Material: Heavy duty steel holding tool and bolts with washers, allow the 280 pounds of torque to be attained Feature: 1.Factory specifications require up to 280 pounds of torque to seat the pulley properly, and our tool allows the factory torque to be attained. 2.Hole in the center of holding tool allows access to the removal of crank shaft bolt. 3.Low profile design, no need to remove radiator or other components to access and remove Harmonic Damper Pulley. 4.Offset breaker bar attachment point allows easy removal and replacement of crank shaft bolt to factory torque specifications. Package includes: 1*Harmonic Damper Pulley Holding Tool 2* bolts & 2 washers Buy it with confidence ! You Won't Regret to Get Sunluway Harmonic Damper Pulley Holding Tool!

  • Brand: Sunluway
  • ASIN: B07QKTG6RX

ABN Universal Harmonic Balancer Puller & Installer 52-Piece Tool Kit - Master Balancer & Pulley Removal/Installation Set

ABN Universal Harmonic Balancer Puller & Installer 52-Piece

Gone are the days of relentlessly tapping your vehicle's harmonic balancer with a hammer and wooden block for ineffective and time-consuming removal. To safely install or remove harmonic balancers and drive pulleys, use the ABN Universal Harmonic Balancer Puller & Installer 52-Piece Tool Kit - Master Balancer & Pulley Removal/Installation Set. Every engine is different, but you'll generally want to remove the belt from the crankshaft pulley and take off the harmonic balancer mounting bolt with a socket and ratchet. From there, you'll use this tool to take off the balancer from the crankshaft. Reinstalling is the same steps in reverse. Compare the old part and the new part to make sure the bolt hole locations are the same, and always pay attention to the proper torque settings. WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

  • Brand: ABN
  • ASIN: B0748K6R9M
  • UPC: 688295876595

Michigan Motorsports Cam Install Gasket Kit LS Crankshaft Damper Bolt Gen 3 LS1 LS2 LS6 (Gasket Kit)

Michigan Motorsports Cam Install Gasket Kit LS Crankshaft

  • Brand: Michigan Motorsports
  • ASIN: B07N6N7FLT

PIONEER-Harmonic-Balancer-Damper-BOLT-for-Chevy-SB 283 305 327 350 383 7.00" INT BALANCED

PIONEER-Harmonic-Balancer-Damper-BOLT-for-Chevy-SB 283 305 327 350 383 7.00" INT

This listing is for a Pioneer OE-Replacement balancer (damper) and bolt for Chevrolet GEN I small block V-8 engines requiring an internally (neutral) balanced 7" OD balancer. P/N DA-3071 + 859012. Balancer specifications are as follows (all measurements are in inches): ENGINE BALANCE: Internal SAFETY RATING: Not SFI approved DEGREE MARKINGS: Yes OUTSIDE DIAMETER: 6.73" MATERIAL: Nodular iron CONSTRUCTION: Elastomer FINISH: Black painted CRANK BORE: 1.24" NOSE DIAMETER: 1.88" WEIGHT: 8.16 lbs. OVERALL WIDTH: 2.34" FREE SHIPPING TO LOWER 48 States

  • Brand: IE PARTS GROUP
  • ASIN: B07CLCRDSP

ARES 71002 | Harmonic Balancer Puller Set | Remove Damper Pulleys in Tight Engine Compartments Without Removing The Radiator Storage Case Included

ARES 71002 | Harmonic Balancer Puller Set |

Easier Removal Of Damper Pulleys In Tight Engine Compartments This ARES Harmonic Balancer Puller Set provides you with everything you need to remove damper pulleys in tight engine compartments without removing the radiator. With spring-loaded legs for optimal position retention and steel construction, you'll have the extra strength and enhanced design you need to get the job done. Whether you're working on a Chrysler, GM, Mitsubishi, Cadillac, or Oldsmobile, this set is the right fit.  Features:  Includes: 1 pc. 3-jaw puller, 4 pc. Forcing rods, 2 pc. forcing screws, 1 pc. Storage case One forcing screw is 3/8-inch square drive for use with ratchets One forcing screw is 3/4-inch hex drive for use with wrenches or sockets Steel construction Black oxide finish for corrosion resistance Designed for removing damper pulleys in tight engine compartments without removing radiator Spring-loaded legs for optimal position retention For use with a variety of Chrysler, GM, Mitsubishi, Cadillac, and Oldsmobile vehicles

  • Brand: ARES
  • ASIN: B079J6T6JB
  • UPC: 818765027800

ACDelco 24503893 GM Original Equipment Timing Chain Damper Kit with Bolt and Retainer

ACDelco 24503893 GM Original Equipment Timing Chain Damper

ACDelco GM Original Equipment Engine Timing Damper Kits remove unnecessary slack from the timing chain to help prevent chain rattle and excessive component wear, and are GM-recommended replacements for your vehicle’s original components. These original equipment engine timing damper kits contain components that will provide the same performance, durability, and service life you expect from General Motors.

  • Brand: ACDelco
  • ASIN: B004AFEGF6
  • UPC: 707773785041

Rough Country 8731730 4WD 4WD N3 Steering Stabilizer for Jeep TJ, XK, MJ, ZJ, WJ, and GM 2500, 3500 HD

Rough Country 8731730 4WD 4WD N3 Steering Stabilizer

Steering stabilizers are designed to restrain "bump steer" and front end vibration, giving added life to tires, ball joints, and other steering components.

  • Color: 4WD
  • Brand: Rough Country
  • ASIN: B07CRLPG1Z
  • UPC: 843030147044

BMW Genuine Belt Drive Vibration Damper Crankshaft Pulley Bolt 525i 525xi 530i 530xi 528i 528xi 535i 535xi 530xi 535xi X5 3.0si X6 35iX 128i 135i M Coupé X3 3.0i X3 3.0si Z4 3.0i Z4 3.0si Z4 3.0si 128i 135i Z4 30i Z4 35i Z4 35is 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi 323i 328i 328xi 335i 335xi 325xi 328i 32

BMW Genuine Belt Drive Vibration Damper Crankshaft Pulley

E60N-Sedan-528i-(2008-10)E60N-Sedan-528xi-(2008-10)E60N-Sedan-535i-(2008-10)E60N-Sedan-535xi-(2008-10)E60-Sedan-525i-(2006-07)E60-Sedan-525xi-(2006-07)E60-Sedan-530i-(2006-07)E60-Sedan-530xi-(2006-07)E61N-Wagon-535xi-(2008-10)E61-Wagon-530xi-(2006-07)E70-SAV/SUV-X5 3.0si-(2007-10)E71-SAC-X6 35iX-(2008-10)E82-Coupe-128i-(2008-13)E82-Coupe-135i-(2008-10)E82-Coupe-M Coupé-(2011-11)E83N-SAV/SUV-X3 3.0i-(2007-10)E83N-SAV/SUV-X3 3.0si-(2007-10)E85-Roadster-Z4 3.0i-(2006-08)E85-Roadster-Z4 3.0si-(2006-08)E86-Coupe-Z4 3.0si-(2006-08)E88-Convertible-128i-(2008-13)E88-Convertible-135i-(2008-10)E89-Roadster-Z4 30i-(2009-11)E89-Roadster-Z4 35i-(2009-11)E89-Roadster-Z4 35is-(2011-11)E90N-Sedan-323i-(2009-11)E90N-Sedan-328i-(2009-11)E90N-Sedan-328xi-(2009-11)E90N-Sedan-335i-(2009-11)E90N-Sedan-335xi-(2009-11)E90-Sedan-323i-(2005-06)E90-Sedan-323i-(2007-08)E90-Sedan-325i-(2005-06)E90-Sedan-325xi-(2005-06)E90-Sedan-328i-(2006-08)E90-Sedan-328xi-(2006-08)E90-Sedan-330i-(2005-06)E90-Sedan-330xi-(2005-06)E90-Sedan-335i-(2006-08)E90-Sedan-335xi-(2006-08)E91N-Wagon-328i-(2009-11)E91N-Wagon-328xi-(2009-11)E91-Wagon-325xi-(2006-08)E91-Wagon-328i-(2007-08)E91-Wagon-328xi-(2007-08)E92-Coupe-328i-(2007-10)E92-Coupe-328xi-(2007-10)E92-Coupe-335i-(2007-10)E92-Coupe-335xi-(2007-10)E92N-Coupe-328i-(2011-12)E...

  • Brand: BMW
  • ASIN: B00TOUT97M
  • UPC: 706084240461

Schley (SCH64300) Lexus and Toyota Harmonic Damper Pulley Holding Tool

Schley (SCH64300) Lexus and Toyota Harmonic Damper Pulley

Developed to aid in the removal and installation of the crank bolt on Lexus and Toyota engines The bolt is extremely tight and removal is extremely difficult at best Factory specifications require up to 280 pounds of torque to seat the pulley properly. This tool allows the factory torque to be attained This holding tool works with the following engines: Lexus 1990 and later: 3.0 L6, 3.0 V6, 3.3 V6, 4.0 V8, 4.3 V8, 4.7 V8. Toyota 1996 and later: 3.0 V6, 3.3 V6, 4.0 V6, 4.7 V8. also 4 cyl: 1983-1995 22RE, 1995-2004 2RZ & 1995-2004 3RZ This special tool is needed to remove the crank shaft bolt - no factory tool available Hole in center of tool - allows access to removal of crank shaft bolt. Offset breaker bar attachment point - allows easy removal and replacement of crank shaft bolt to factory torque specifications Low profile design - no need to remove radiator or other components to access and remove Harmonic Damper Pulley.

  • Brand: Schley
  • ASIN: B0051XDBBG
  • UPC: 767887389580

JEGS W89711 Universal Harmonic Balancer Puller/Installer

JEGS W89711 Universal Harmonic Balancer

Fits:L98 & LT-Series EnginesLS1 with Aftermarket 3-bolt Style Balancer OnlySmall Block Chevy/Big Block ChevySmall Block Ford/Big Block FordSmall Block Chrysler/Big Block Chrysler Kit Includes:(2) 6" x 5/16" NC Bolts(3) 3-1/2" x 5/16" NC Bolts(2) 3" x 5/16" NF Bolts(3) 1-1/2" x 2/8" NF Bolts(2) 2-1/2" x 1/4" NF Bolts(3) 3" x 3/8" NC Bolts(2) 4-1/2" x 3/8" NC Bolts(3) 2" x 3/8" NC Bolts(2) 90mm M8 x 1.25 Bolts(2) 65mm M8 x 1.25 Bolts(3) 45mm M8 x 1.25 Bolts(3) 35mm M10 x 1.5 Bolts(2) 1/4" Washers(3) 10mm Washers(3) 5/16" Washers(3) 8mm Washers(1) M16 x 2.0 Adapter(1) M14 x 1.5 Adapter(1) M12 x 1.5 Adapter(1) 3/4" Adapter(1) 5/8" Adapter(1) 9/16" Adapter(1) 1/2" Adapter(1) 7/16" Adapter(1) 5" Puller Screw(1) Puller Flange(1) Puller Body(1) Centering Adapter(1) Complete Instructions(1) Carrying Case

  • Brand: JEGS
  • ASIN: B007WWS2FY
  • UPC: 889944002567

Capri Tools 21000 Honda Crank Pulley Removal Tool

Capri Tools 21000 Honda Crank Pulley Removal

This Capri Tools Honda crank pulley removal tool allows for easy loosening or tightening the crank pulley bolt in most Honda or Acura engines by preventing the engine from turning. Features a professional grade 50 mm socket compatible with 1/2-inch drive breaker bar. Constructed with hardened Chrome-Molybdenum steel alloy for maximum strength. Extremely durable and compact for access to tight engine spaces. Backed by a lifetime replacement guarantee.

  • Color: Black
  • Brand: Capri Tools
  • ASIN: B00I3RLMIG
  • UPC: 886352210003

CTA Tools 2237 Toyota/Lexus Harmonic Dampening Tool

CTA Tools 2237 Toyota/Lexus Harmonic Dampening

CTA Tools 2237 Toyota / Lexus Harmonic Dampening Tool holds the crankshaft while tightening the crank bolt. Fits Toyota '96 and up 3.0, 3.3, 4.0, V6, 4.7, V8 plus '83 - '95 4-cyl. 22RE, '95 - '04 4-cyl., 2.4 RZ and 2.7 3RZ, plus Lexus '90 and up 3.0 L6, 3.0, 3.3 V6 and 4.0, 4.3 and 4.7 V8 engines. California Prop 65 - Warning, This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

  • Brand: CTA Tools
  • ASIN: B005OH0IWO
  • UPC: 053001022373

Danti 19 mm Harmonic Balancer Socket Use for 19mm Hex Pulley Damper Bolt for Honda

Danti 19 mm Harmonic Balancer Socket Use for

Product Feature Made of High Standard Quality of GB 40CR Alloy Steel Used on Honda engines which use with 1/2" drive Package Include: 1 * Danti 19 mm Harmonic Balancer Socket

  • Brand: Danti
  • ASIN: B07CHZR7V4

Rockford Chimney Supply Stainless Steel Premier Chimney Damper Cap with Mounting Bolts, 9x13 Inch

Rockford Chimney Supply Stainless Steel Premier Chimney Damper

The 9" x 13" Premier Chimney Damper Cap fits clay flue tiles with an outside dimensions between 8" x 12" to 10" x 14". What sets the Premier Damper Cap apart from the rest? It's the only damper cap manufactured in the industry with mounting bolts for an easy installation for homeowners. Made in the USA with a 304 stainless steel 1/2" thick insulated lid that provides extra protection from condensation. The Premier Chimney Damper Cap has a lid that's 15% larger than most other damper caps so it can provide the best protection from the elements limiting ice and snow build-up even in the harshest of weather. It seals tightly against a high temperature gasket bonded with high temperature silicone. The gasket and silicone together are made to withstand temperatures ranging from -85 to +450 degrees Fahrenheit. This damper cap also features a 3/4" expanded mesh screen, removable lid for easy cleaning, 50 foot cable, and lifetime warranty!

  • Color: Stainless Steel
  • Brand: Rockford Chimney Supply
  • ASIN: B00R3LZNDI

Sunluway Harmonic Damper Pulley Holding Tool Crankshaft Crank Holder for Toyota Tacoma 4Runner Tundra T100 Pickup/Trucks Engine

Sunluway Harmonic Damper Pulley Holding Tool Crankshaft Crank

Wanna Save Energy and Time When Removing and Installing the Crank Bolt ? Sunluway tool is a lifesaver if you work on Toyota timing belts or just need to remove the crankshaft pulley. Fitment: Toyota 3.4L V6 Tacoma 1996-2004, 4 Runner 1996-2002, Tundra 2000-2004, T100 pickup 1996-1998 Time-saver: The tool in combination with a 1/2" breaker bar braced against the frame make short work of the crankshaft bolt. Even when torquing the bolt to over 200 ft. Pounds, the tool can hold the crank with no problem. This tool definitely cut about an hour off the job! Caution: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. Package includes: 1*Harmonic Damper Pulley Holder Buy it with confidence ! You Won't Regret to Get Sunluway Harmonic Damper Pulley Holding Tool!

  • Brand: Sunluway
  • ASIN: B07QKV56B3

OEMTOOLS 25090 Harmonic Balancer Puller for GM, Chrysler, Cadillac, Chevy Trucks, Ford, and Mitsubishi - No Need to Remove The Radiator

OEMTOOLS 25090 Harmonic Balancer Puller for GM, Chrysler,

The OEMTOOLS Harmonic Balancer Puller is designed for use with Model GM 2000 Generation II, Cadillac (1988 and later), Chevrolet Trucks (2003 and later), Chrysler (1990 and later), Ford (1995 and later), and Mitsubishi Eclipse (1995)—designed for removing damper pulleys in tight engine compartments without removing the radiator. Includes 3 Jaw Puller, Forcing Rods (4 lengths included), and a Forcing Screw with a 3/8” square drive for ratchet use, and a ¾” hex for wrench or socket use. The OEMTOOLS Harmonic Balancer Puller includes unique tensioned jaws which makes for easy tool placement in tight quarters—a feature only found on the OEMTOOLS puller.

  • Brand: OEMTOOLS
  • ASIN: B01AIRR4EY
  • UPC: 076812134868

Hitachi 6698859 Damper Set Bolt

Hitachi 6698859 Damper Set

Hitachi Power Tools (Hitachi Koki USA, Ltd.) provides professional-grade power tools for a variety of applications, including woodwork, metalwork, concrete, drilling, cutting, and outdoor power equipment. Hitachi is a leader in power tool research and development and has achieved many firsts in the power tool industry, including creating the first-ever sliding compound miter saw to combine the capacity of a radial arm saw and the convenience of a miter saw. Today, Hitachi continues the tradition of innovation and engineering with its new line of commercial grade outdoor power equipment.

  • Brand: Hitachi
  • ASIN: B00EOI7B88
  • UPC: 719592698853

LAND ROVER DISCOVERY 2 1999-2004 STEERING DAMPER ASSEMBLY PART QHH100001

LAND ROVER DISCOVERY 2 1999-2004 STEERING DAMPER ASSEMBLY

LAND ROVER DISCOVERY 2 1999-2004 STEERING DAMPER ASSEMBLY QHH100001 ***** BRAND NEW - BRITPART PART NUMBER QHH100001 ****** New Steering damper assembly which fits all Discovery models from 1999 to 2004. This part can be used either side on the front. ****** Fitting bolt part number ANR1193 & Nut part number ANR1000 are not included ***** Models Affected: Land Rover Discovery Series II 1999 - 2004

  • Brand: BRITPART
  • ASIN: B077J83GQZ
  • UPC: 751446378146

New Big Crank Shaft Damper Pulley Bolt 91-05 For Miata MX5 B3C711406 OEM

New Big Crank Shaft Damper Pulley Bolt 91-05

  • Brand: Generic
  • ASIN: B07NPMX693

OTC 4731A Damper Holding Tool for Acura and Honda

OTC 4731A Damper Holding Tool for Acura and

The OTC Honda/Acura Damper Holding Tool holds the damper for removal and installation of the crank bolt on most Honda/Acura engines. Can remove and install the damper so engine will not rotate. The tool has a 4 inch offset, 50 millimeters hex with large center hole, and a 1/2 inch square drive can be used with ratchet or breaker bar. Proper fit for applications and allows use of impact tool to remove bolt and will fit around accessories eliminating additional part removal. Works on Honda Accord, Civic, CRV, Del Sol, Element, Fit, Insight, Odyssey, Pilot, Prelude, Ridgeline, S2000 and Acura CL, Integra, Legend, MDX, RL, RSX, TL, TSX.

  • Brand: OTC
  • ASIN: B003XEYKAG
  • UPC: 731413557811

Rock Shox Rebound Adjuster Knob/bolt Kit Boxxer (charger Damper) (35 Mm),

Rock Shox Rebound Adjuster Knob/bolt Kit Boxxer (charger

For MissionControl (MiCo), MissionControl-DH (MiCo-DH), MotionControl (MoCo), MotionControl-IS (MoCo-IS), and Turnkey dampers

  • Brand: Rock Shox
  • ASIN: B00L2PWQUE
  • UPC: 710845752360

Harmonic Balancer Puller Set Flange-Type Puller Crankshaft pulleys Set with Master Bolt Grip Set- (Grade 8)- By Kauplus

Harmonic Balancer Puller Set Flange-Type Puller Crankshaft pulleys

The Kauplus Flange-Type Puller Set idea for pulling balancers, vibration dampers, pulley and gears with the tapped holes, capable of handling 2 or 3-way bolt pulling applications, works on most of vehicles i.e. pickups, SUVs and small engines. Multi-purpose components of the Master Bolt Grip Set is designed for use on steering wheels, crankshaft pulleys, gears and harmonic balancers, set Made in Taiwan and contains 1pc heavy duty forged three-way puller flange/yoke (with four slots, which allow the article to be used for two or three holes applications.), 2pcs of different length live -center forcing screws, 3" and 6", 4pcs of live-center adapters, 3 pieces of special shoulder bolts (1/4-28UNF*3-1/4") for GM 3300-3800 V6, and 11 set of Heavy duty washer heard hardened steel bolts (Grade 8): 5/16-18UNC*3.5", 5/16-24UNF*3", 1/4-28UNF*3" 3/8-24UNF*1.5", 3/8-16UNC*2", 3/8-16UNC*3", 3/8-16UNC*4.5", M8*1.25*45mm, M8*1.25*65mm, M8*1.25*90mm, M10*1.5*35mm. Come in blow case for complete storage. Caution For prevent serious injury it is necessary to wear safety goggles on any work position.

  • Color: metallic
  • Brand: Kaupa
  • ASIN: B074SGM57M
  • UPC: 682698742051

8MILELAKE 50mm Hex Crankshaft Crank Damper Pulley Holding Wrench Socket Tool Compatible for Honda Acura Cars

8MILELAKE 50mm Hex Crankshaft Crank Damper Pulley Holding

Works on the following Honda and Acura engines: 1990-1997 Honda Accord 2.2L 4 cyl. 1996-1997 Honda Accord 2.7L V-6 1998-newer Honda Accord 2.3L 4 cyl. & 3.0L V-6 1992-newer Honda Civic 1.6L 4 cyl. 1997-newer Honda CR-V 2.0L 4 cyl. 1993-1997 Honda Del Sol 1.6L 4 cyl. 2000-newer Honda Insight 1.0L 3 cyl. 1995-1997 Honda Odyssey 2.2L 4 cyl. 1998 Honda Odyssey 2.3L 4 cyl. 1999-newer Honda Odyssey 3.5L V-6 1992-newer Honda Prelude 2.2L 4 cyl. 1992-1996 Honda Prelude 2.3L 4 cyl. 2000-newer Honda S2000 2.0L 4 cyl. 1997 Acura CL 2.2L 4 cyl. 1997-1998 Acura CL 3.0L V-6 1998-1999 Acura CL 2.3L 4 cyl. 2000-newer Acura CL 3.2L V-6 1990-1992 Acura Integra 1.6L 4 cyl. 1992-1993 Acura Integra 1.7L 4 cyl. 1993-newer Acura Integra 1.8L 4 cyl. 1991-1995 Acura Legend 3.2L V-6 1996-newer Acura RL 3.5L V-6 1995-newer Acura TL 3.2L V-6

  • Brand: 8MILELAKE
  • ASIN: B0183KQ1JC
  • UPC: 700425112783

Euone ♛ Door Damper, Deadbolt Bump Key Safety Security Travel Home Anti Bumping Lock

Euone ♛ Door Damper, Deadbolt Bump Key Safety

❀Welcome to EShocking , may you have a pleasant shopping experience! If you have any problems about our products, please feel free to contact us at any time, we will try our best to help you, thanks in advance! 🌞🌞♥ Please check your shipping address, name and the phone number carefully before buying. 🌞🌞 The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness. 🌞🌞Specification: 🌞🌞This stands guard against ALL unwanted intruders! This is especially designed to deter unwanted entry into your home by people with keys or intruders using the "Key-Bumping" method. Let  it guard your doors against illegal tampering and entry! 🌞🌞Easily attatches to most deadbolt locks, quickly and effortlessly and INSTALLS WITHOUT ANY TOOLS! 🌞🌞Made from high grade materials, the durable frame can withstand alomost anything you can throw at it. 🌞🌞A great product for: 🌞🌞- Seniors 🌞🌞- Women  🌞🌞- Handicapped indivivuals 🌞🌞- Families 🌞🌞- College Students 🌞🌞Keeps Out Any one with...

  • Color: As Shown
  • Brand: Euone
  • ASIN: B07SRX4GCF
  • UPC: 745344222120
Similar Damper Bolt Shopping Results